Q647F-16C Pneumatic Handwheel Carbon Steel Two Piece Fixed Ball Valve

Product Overview

The Q647F-16C Pneumatic Handwheel Carbon Steel Two Piece Fixed Ball Valve is used in the mining, refining, processing, and pipeline transportation systems of oil, natural gas, coal, and ore; Pneumatic valves are used in the production of chemical products, pharmaceuticals, and food; In the power production systems of hydropower, thermal power, and nuclear power; In the water supply and drainage, heating, and gas supply systems of cities and industrial enterprises; In the irrigation and drainage system of farmland; Pneumatic ball valves are widely used in metallurgical production systems, and are sealed in various pipeline systems to cut off or connect the flow of media, so that the media is transported to designated points according to predetermined procedures.

There are two types of valve body structures: two-piece and three piece. The middle flange is connected by bolts, and the seal is made of reinforced polytetrafluoroethylene embedded in a stainless steel ring. There is no spring at the back of the steel ring to ensure that the valve seat is tightly attached to the ball, maintaining sealing. There are no PTFE bearings on both the upper and lower valve stems, reducing friction and making operation effortless. There are no adjustment plates at the bottom of the small shaft to ensure the joint position between the ball and the sealing ring. Full bore: The valve flow aperture is consistent with the inner diameter of the pipeline for pipeline cleaning.

Performance Characteristics

• Effortless operation: The ball is supported by upper and lower bearings, reducing friction and eliminating excessive torque caused by the huge sealing load formed by the inlet pressure pushing the ball and the sealing seat.
• Reliable sealing performance: The PTFE single sex material sealing ring is embedded in the stainless steel valve seat, and the metal valve seat end is equipped with a spring to ensure sufficient pre tightening force of the sealing ring. When the sealing surface of the valve wears out during use, the valve continues to ensure good sealing performance under the action of the spring.
• Fireproof structure: In order to prevent the PTFE sealing ring from burning out due to sudden heat or fire, causing significant leakage and fueling the fire, a fireproof sealing ring is installed between the sphere and the valve seat. When the sealing ring burns out, the valve seat sealing ring is quickly pushed onto the sphere by the spring force, forming a metal to metal seal and achieving a certain degree of sealing effect. The fire resistance test meets the requirements of APl6FA and APl607 standards.
• Automatic pressure relief function: When the pressure of the stagnant medium in the valve chamber abnormally increases beyond the preload force of the spring, the valve seat will retract and detach from the ball, achieving the effect of automatic pressure relief. After pressure relief, the valve seat will automatically reset.
• Drain pipeline: Drain plugs L are installed on both the upper and lower parts of the valve body to check if there is any leakage in the valve seat. During operation, when the valve is fully open or fully closed, the pressure in the middle chamber can be relieved and the packing can be directly replaced; It can discharge the retained substances in the middle chamber and reduce the pollution of the medium to the valve. Auxiliary sealing setting system (please specify when ordering).
• This valve is designed with an auxiliary seat emergency sealing system. Once the seal is damaged or an emergency situation occurs and cannot be sealed, the corresponding sealing agent can be injected into the sealing surface through the auxiliary sealing system to repair the sealing surface and achieve emergency sealing. When the conveyed medium is unclean or contains a small amount of particles, in order to protect the sealing surface and ensure reliable sealing, corresponding cleaning agents or lubricants can be injected into this device to clean the sealing surface.

Product Commitment

1. Quality commitment: All types of valves provided by our factory are designed, manufactured, tested and accepted in accordance with relevant domestic standards such as GB, JB, SH, HG, CJ, as well as international standards such as ANSI, JIS, BS, DIN, etc;
2. Supply commitment: Ruiward Valve guarantees to provide brand new defect free products, as well as relevant drawings and other technical documents related to the products, to ensure that users have no worries during use;
3. Service commitment: The product warranty period is 12 months from the date of delivery, and the “three guarantees” service (return, replacement, and repair) is implemented.

Ruiward valve products are exported to Europe, America, Southeast Asia and other countries with reasonable prices, stable quality, and perfect after-sales service. It is your trusted brand. Welcome to call 86-577-88937087 for inquiries!

Ordering Instructions

1. If the product model of Ruiward Company has been selected by the design unit, please order directly from our sales department or affiliated regional business office according to the model;
2. If the model has not been selected before ordering, please provide us with the following usage parameters: ① nominal diameter (DN), ② fluid properties (including nominal pressure (Mpa), temperature (℃), pressure difference before and after the valve, connection method (thread, flange, clamp), viscosity or acidity, etc.), ③ valve body and core materials;
3. Product driving modes: manual, worm gear, self operated, pneumatic, electric, etc;
4. Product standards: National Standard GB, Japanese Standard JIS, American Standard ANSI, German Standard DIN, British Standard BS, European Standard EN, etc;
5. When the application is very important or the pipeline is complex, please provide design drawings and detailed parameters as much as possible, and the technical team of Ruiward Company will review and control them for you;
6. Our company provides a quotation list and technical standard specifications for customer confirmation, and the contract will be drafted after both parties confirm the technical aspects.